RESUMO
The literature rarely compiles studies devoted to the removal of pollutants in aqueous media comparing adsorption and photocatalytic degradation, and does not pay enough attention to the analysis of combined adsorption-photocatalytic oxidation processes. In the present manuscript, the removal of malachite green (MG) from aqueous solutions has been investigated in three different sustainable scenarios: i) adsorption on activated carbon (AC) derived from a residue, luffa cylindrica, ii) photocatalytic oxidation under simulated solar light using titanium dioxide (TP) and iii) combined adsorption-photocatalytic oxidation using TP-AC (70/30 wt./wt.) under simulated solar light. The study has revealed that in the three scenarios and studied conditions, the total removal of this endocrine-disrupting dye from the solution takes place in the assayed time, 2 h, in some cases just in a few minutes. MG adsorption in the AC is a very fast and efficient removal method. MG photocatalytic oxidation with TP also occurs efficiently, although the oxidized MG is not totally mineralized. MG removal using the TP-AC composite under simulated solar light occurs only slightly faster to the MG adsorption in the AC, being adsorption the dominating MG removal mechanism for TP-AC. Thus, more than 90% of the removed MG with TP-AC under simulated solar light is adsorbed in this carbon-containing composite. The obtained results highlight the interest in adsorption, being the selection of the most suitable removal method dependent on several factors (i.e., the cost of the AC regeneration, for adsorption, or the toxicity of the intermediate oxidation species, for photooxidation). Paying attention to MG photooxidation with TiO2, comparison of two working photodegradation schemes shows that the direct photodegradation of MG from solution, avoiding any initial dark equilibrium period, is more efficient from a time perspective. The use of scavengers has proved that MG photodegradation occurs via an oxidation mechanism dominated by superoxide anion radicals.
RESUMO
A series of nanostructured boron-TiO2 photocatalysts (B-X-TiO2-T) were prepared by sol-gel synthesis using titanium tetraisopropoxide and boric acid. The effects of the synthesis variables, boric acid amount (X) and crystallization temperature (T), on structural and electronic properties and on the photocatalytic performance for propene oxidation, are studied. This reaction accounts for the remediation of pollution caused by volatile organic compounds, and it is carried out at low concentrations, a case in which efficient removal techniques are difficult and costly to implement. The presence of boric acid during the TiO2 synthesis hinders the development of rutile without affecting the textural properties. X-ray photoelectron spectroscopy analysis reveals the interstitial incorporation of boron into the surface lattice of the TiO2 nanostructure, while segregation of B2O3 occurs in samples with high boron loading, also confirmed by X-ray diffraction. The best-performing photocatalysts are those with the lowest boron loading. Their high activity, outperforming the equivalent sample without boron, can be attributed to a high anatase and surface hydroxyl group content and efficient photo-charge separation (photoelectrochemical characterization, PEC), which can explain the suppression of visible photoluminescence (PL). Crystallization at 450 °C renders the most active sample, likely due to the development of a pure anatase structure with a large surface boron enrichment. A shift in the wavelength-dependent activity profile (PEC data) and the lowest electron-hole recombination rate (PL data) are also observed for this sample.
RESUMO
Chiral rhodium hybrid nanocatalysts have been prepared by covalent anchorage of pyrrolidine-based diphosphine ligands onto functionalized CNTs. This work constitutes the first attempt at covalent anchoring of homogeneous chiral catalysts on CNTs. The catalysts, prepared with two different chiral phosphines, were characterized by ICP, XPS, N2 adsorption and TEM, and have been tested in the asymmetric hydrogenation of two different substrates: methyl 2-acetamidoacrylate and α-acetamidocinnamic acid. The hybrid nanocatalysts have shown to be active and enantioselective in the hydrogenation of α-acetamidocinnamic acid. A good recyclability of the catalysts with low leaching and without loss of activity and enantioselectivity was observed.
RESUMO
Hybrid catalysts have been prepared by the immobilization of a Rh complex on carbon nanotubes and nanofibres. To tether the complex, a siloxane type bond has been created by reaction of a trimetoxisilane end of a ligand and -OH phenol type groups on the supports surface. The hybrid catalysts have been tested in the hydrogenation of three different substrates: cyclohexene (as a test for activity), carvone (to analyze the chemoselectivity) and 2-metyhl acetamidoacrylate (to evaluate enantioselectivity, using BINAP as chiral ligand). The obtained results show that the hybrid catalysts are more active than the homogeneous complex. The enhanced activity has been related to a confinement effect, produced as a consequence of the metal complex location inside the tubular structures of the supports. The enantioselectivity is opposite for the heterogenized and the homogeneous complex. Some differences have been found between the properties of catalysts prepared with nanotubes and nanofibres, which have been related to differences in the tube inner diameter.
